Who does not have a flash memory USB drive? (128Mb – 16Gb…) Everybody does, even my dog, if I had one, would have it. However, sometimes these little dongles can be tricky to use if they are not properly formatted. The usual format for the flash memory USB drive is FAT16, and it is understood by many operating systems with no problem. But in case the drive is not formatted properly/or you think it is not formatted properly, you can always reformat it, and here is how.
The whole process consists of 5 steps ans takes about 15 seconds um.. if do it slowly.. :)
In case you need to find the actual device your USB drive was associated with look here “Find USB flash device/drive in Linux“
WARNING: All the data will be lost from the flash UBS drive since we are going to reformat it.
We are going to use fdisk utility, so “for starters” here are available commands that you can use with fdisk:
a – toggle a bootable flag
b – edit bsd disklabel
c – toggle the dos compatibility flag
d – delete a partition
l – list known partition types
m – print this menu
n – add a new partition
o – create a new empty DOS partition table
p – print the partition table
q – quit without saving changes
s – create a new empty Sun disklabel
t – change a partition’s system id
u – change display/entry units
v – verify the partition table
w – write table to disk and exit
x – extra functionality (experts only)
Now let’s get to cooking a new and fresh flash memory USB drive…
Step 1. Run fdisk via sudo on your USB flash drive device:
user@host:~$ sudo fdisk /dev/sdb |
user@host:~$ sudo fdisk /dev/sdb
enter “p” command to list current partition table of the USB drive:
Command (m for help): p
Disk /dev/sdb: 1039 MB, 1039663104 bytes
32 heads, 62 sectors/track, 1023 cylinders
Units = cylinders of 1984 * 512 = 1015808 bytes
Disk identifier: 0xf1f494df
Device Boot Start End Blocks Id System
/dev/sdb1 1 1023 1014785 83 Linux |
Command (m for help): p
Disk /dev/sdb: 1039 MB, 1039663104 bytes
32 heads, 62 sectors/track, 1023 cylinders
Units = cylinders of 1984 * 512 = 1015808 bytes
Disk identifier: 0xf1f494df
Device Boot Start End Blocks Id System
/dev/sdb1 1 1023 1014785 83 Linux
Here you will see whatever partition (if any) currently present. In my case (above) it is a “Linux” partition, in your case it may be something different. But it does not really matter, because we are going to delete it anyway:
Step 2. Enter “d” command to delete existing partition (if you have any). If you have several, delete several by using”d” command multiple times:
Command (m for help): d
Selected partition 1 |
Command (m for help): d
Selected partition 1
Step 3. Now let’s get to business and enter “n” command to create a new partition:
Command (m for help): n
Command action
e extended
p primary partition (1-4)
p
Partition number (1-4): 1
First cylinder (1-1023, default 1):
Using default value 1
Last cylinder or +size or +sizeM or +sizeK (1-1023, default 1023):
Using default value 1023 |
Command (m for help): n
Command action
e extended
p primary partition (1-4)
p
Partition number (1-4): 1
First cylinder (1-1023, default 1):
Using default value 1
Last cylinder or +size or +sizeM or +sizeK (1-1023, default 1023):
Using default value 1023
As you can see from above, I entered “1” for “Partition number”, and hit enter key twice to leave everything by default.
Now let us list current partitions with “p” command again:
Command (m for help): p
Disk /dev/sdb: 1039 MB, 1039663104 bytes
32 heads, 62 sectors/track, 1023 cylinders
Units = cylinders of 1984 * 512 = 1015808 bytes
Disk identifier: 0xf1f494df
Device Boot Start End Blocks Id System
/dev/sdb1 1 1023 1014785 83 Linux |
Command (m for help): p
Disk /dev/sdb: 1039 MB, 1039663104 bytes
32 heads, 62 sectors/track, 1023 cylinders
Units = cylinders of 1984 * 512 = 1015808 bytes
Disk identifier: 0xf1f494df
Device Boot Start End Blocks Id System
/dev/sdb1 1 1023 1014785 83 Linux
We have a single “Linux” partition which is fine (for now).
Step 4. Time to actually apply our changes, so enter a “w” command that will write out all the changes to the USB drive.
Command (m for help): w
The partition table has been altered!
Calling ioctl() to re-read partition table.
Syncing disks. |
Command (m for help): w
The partition table has been altered!
Calling ioctl() to re-read partition table.
Syncing disks.
fdisk will write all the changes to the USB drive and exit. But we are not done yet. Our goal is to make a (in this case) FAT16 partition, so this USB drive can be read by most operating systems.
Step 5. For that we will use mkfs.vfat utility:
user@host:~$ sudo mkfs.vfat -F 16 /dev/sdb1
mkfs.vfat 2.11 (12 Mar 2005) |
user@host:~$ sudo mkfs.vfat -F 16 /dev/sdb1
mkfs.vfat 2.11 (12 Mar 2005)
Now we are good to go! It was easy, as I promised :)
Let’s look at the new USB drive now. Mounting it first:
user@host:~$ sudo mount /dev/sdb1 /mnt/flashka/
user@host:~$ cd /mnt/flashka/
user@host:/mnt/flashka$ ls -l
total 0 |
user@host:~$ sudo mount /dev/sdb1 /mnt/flashka/
user@host:~$ cd /mnt/flashka/
user@host:/mnt/flashka$ ls -l
total 0
Checking what it has under the hood:
user@host:/mnt/flashka$ df -h
Filesystem Size Used Avail Use% Mounted on
/dev/sdb1 991M 0 991M 0% /mnt/flashka
user@host:/mnt/flashka$ |
user@host:/mnt/flashka$ df -h
Filesystem Size Used Avail Use% Mounted on
/dev/sdb1 991M 0 991M 0% /mnt/flashka
user@host:/mnt/flashka$
It has 991Mb which is what they call 1Gb flash memory USB drive! :)
Ever heard about rails.vim project? “Accept no imitations: rails.vim is the one true Vim plugin for syntax highlighing, easy navigation, and script invocation for all your Ruby on Rails applications, transparently and unobtrusively” says creator Tim Pope.
Frequently I need to access my 
Sometime ago ASUS rebranded some of their motherboards as “Express Gate”.